This report deals with the performance of a batch flow treatment of landfillleachate compared with a continuous flow system. The parameters in focus were total Kjeldahl nitrogen (TKN), BOD5 and COD. The pilot-scale experiment used eight barrels with a volume of 150 liters. Each barrel was constructed differently concerning its flow, its bed material grain size and its presence of plants or not. Four of the barrels worked in batch mode, thus four in continuous flow mode.

Four different kinds of filter-materials with reactive surfaces have been studied concerning their capacity to absorb heavy metals in leachate from a municipal waste deposit. The heavy metals studied were: lead, cadmium, copper, mercury, chromium, nickel and zinc. The leachate contains high levels of dissolved organic carbon (DOC) and has a high pH-value along with a high buffer capacity. These characteristics of the leachate make it difficult to remove pollutants and require efficient filters. The filters that were examined in the report are blast-furnace slag with CaO, sand covered with iron oxides, olivine and nepheline.

Käppala wastewater treatment plant situated on the island of Lidingö northeast of Stockholm is running a project during 2004 and 2005 with the purpose to map out the capacity of anaerobic digestion in the digesters that treat primary and excess sludge. The purpose of this thesis work, which is part of that project, was to characterize the present anaerobic digestion process and to investigate its capacity to treat other organic wastes such as restaurant waste and waste from water works. To decide the potential of both methane and biogas production from different substrates batch laboratory tests were carried out. To imitate the anaerobic digestion process at Käppala continuous tests with small scale reactors were carried out. These reactors were later fed with restaurant waste.The batch laboratory tests showed that primary sludge had a potential biogas and methane production of 0,62 and 0,35 Ndm3/g VS respectively after 40 days of digestion.

This essay begins with a literature study of the different propagation methods for roses, and a survey of the factors affecting the rooting of cuttings in general and rose cuttings in particular. The main part of the essay consists of a practical study of the rooting of rose cuttings. I have chosen to examine how the time of year when the cuttings are taken, and the position of the cuttings influence the rooting. Three different cultivars were used as mother plants; ?Maria Lisa? and two Burnet roses; ?King of Scots? and ?Poppius?. The mother plants were container grown ?King of Scots? and ?Maria Lisa?, and outdoor grown ?Poppius? and ?Maria Lisa?.

Using leaching test is a way to get a picture of pollutants retention and leaching in a risk assessment on contaminated land. There are several different types of standardised leaching tests today, where the natural leaching processes are speeded up to make it possible to predict the leaching of pollutants. These leaching tests have been developed for waste and there are no specific guidelines on how to judge the results from the tests, when making a risk assessment on contaminated land. This work is an investigation on how to use leaching test in this type of risk assessments. The strengths and weaknesses of the different types of tests are discussed. Depending on what type of information you want from your leaching test, different types of tests are suitable.

The work with this report has been focused on developing a methodology model for control at purchase. The methodology model covers parts classification, dispatching systems, batch shaping and more. The aim with the methodology model is that it will be used as an aid for a cost effective material planning to increase the value for customer.The work covers also a description of the present situation and the purchase process at Company X. Six parts have been applied, two from each class (A, B and C), in the methodology/model. The parts that have been applied are included in the flow between Company X and their supplier Company Y.Data have been collected trough literature studies, interviews and the company?s business system.

Mine waste from Ljusnarsbergsfältet in Kopparberg, Sweden, is considered to constitute a great risk for human health and the surrounding environment. Some of the waste rock consists of sulphide minerals. When sulphide minerals come into contact with dissolved oxygen and precipitation, oxidation may occur resulting in acid mine drainage (AMD) and the release of heavy metals. The purpose of this study has been to characterise the waste material and try to chemically stabilize the waste rock with a mixture of sewage sludge and calcium carbonate. The drawback of using organic matter is the risk that dissolved organic matter can act as a complexing agent for heavy metals and in this way increase their mobility.

Saab Training Systems (STS) in Huskvarna is manufacturing material for educationalpurposes to armies worldwide. They are now implementing parts of the Lean productionconcept in their organisation.One part of the work with Lean production is to eliminate waste. To be able to identify waste,value stream mapping is a good tool and also what we used in our thesis. To gain a betterefficiency in the production of Personnel Detector Device (PDD) flow was one of our goals.The PDD is a harness used during battle training which registers if the user is being hit by itsenemy.Our work with the thesis started up with a short education in Lean production and in valuestream mapping (VSM). The work proceeded with a VSM of the production flow of the PDD,interviews were made and studies of literature were done to gain greater knowledge of thesubject and solve the task.The VSM resulted in five areas which were followed up out of those six we identified.

This master's theses was carried out on assignment from Stockholm Vatten AB as a part of a project developing new waste water treatment techniques. The goal of the theisis has been to evaluate an anaerobic membrane bioreactor for treatment of waste water from Hammarby Sjöstad. The bioreactor has not been heated and the main interest has been to study the gas production, power consumption and the reduction of organic matter and nutrients.The system has been completed with a reverse osmosis unit and a total of four batch runs have been made with good results. The use of reverse osmosis allows nutrient in the waste water to be reintroduced into circulation as the reverse osmosis concentrate can be used as crop nutrient.The membrane unit is of VSEP ("Vibratory Shear Enhanced Processing") type and an extensive membrane test has been conducted. This so called L-test helped determine the most suitable type of membrane for the system to allow a higher ±ux and thus lower power consumption.

The component workshop at Atlas Copco inTierp intends to reduce the costs inorder to increase their competitiveness.This thesis examines how the productionmanagement around cylinder washersshould be managed in a way that meetsthe customer needs. The customer to thecylinder washer is Atlas Copcos assemblydepartment in Tierp.The purpose of this thesis is to providean alternative way of managing theproduction. A chapter of theory is addedto give the reader an insight ofdifferent types of production managementsystems as well as the underlyingknowledge needed to get a better readingexperience. An introduction of kanbancan in theory help Atlas Copco in thedirection they strive. It should beclear how the purpose of this thesisaffects the cost for the componentworkshop and also how it relates to thecurrent production.

Test is an area in system development. Test can be performed manually or automated. Test activities can be supported by Word documents and Excel sheets for documenting and executing test cases and as well for follow up, but there are also new test tools designed to support and facilitate the testing process and the activities of the test. This study has described manual test and identified strengths and weaknesses of manual testing with a testing tool called Microsoft Test Manager (MTM) and of manual testing using test cases and test log templates developed by the testers at Sogeti. The result that emerged from the problem and strength analysis and the analysis of literature studies and firsthand experiences (in terms of creating, documenting and executing test cases) addresses the issue of the following weaknesses and strengths.

Test bench for air bearingsThis thesis work consisted of bringing forward and defining the test parameters relevant for a test bench and constructing a test bench that can test and verify the largest existing air bearings that are of use in Micronic Laser Systems AB machines. Because the knowledge about air bearings is limited it is thought that with the help of the test bench the knowledge would increase and in that way improve the air bearings.After learning more about air bearings and their purpose at Micronic Laser Systems AB, I started the concept phase for the test bench. For each part in the test bench I consulted my two tutors, Torbjörn Hedevärn and Johan Bergqvist, at Micronic Laser Systems AB. The final concepts where documented as 3D-modells in Solidworks and some of them have been tested in Solidworks FEM-program.The test bench is designed so that, with the help of a pneumatic cylinder, 25 kilo weights are placed on the air bearing to test its stiffness, damping and the pressure performance under its surface area. To test these parameters the test bench has to have a pressure meter, accelerometer and a microcator.

This paper investigates the usability of the intelligence test Wechsler Nonverbal Scale of Ability (WNV). Twenty four children in two different age-groups were tested with WNV, 10 children between ages 5 - 6, and 14 children between ages 9 - 10. The WNV turned out to be a useful test when some verbal communication was used in the test situation. This was especially apparent among the younger children, who needed extra verbal instructions and verbal support through the different subtests. The test also contained standardized verbal instructions for all ages.

Most of the city of Uppsala rests on postglacial clay with a varying content of sulphur. The sulphur occurs naturally in the clay in reduced form as sulphide and the clay is for that reason usually called ?sulphide clay?. Excavation during construction activities gives rise to large amounts of excavation material, of which the sulphide clay is a considerable part.When the clay is exposed to air and water, an oxidation of the sulphides occurs which may produce an acid leachate and the mobilisation of heavy metals bound in the clay or underlying material. The aim of the work has been to improve our understanding of the behaviour of sulphide clays and produce a basis for risk assessment in the future handling of excavation material with high sulphide content.

In organic animal production, synthetic amino acids are not allowed. Therefore, a higher level of crude protein is needed in the diet to pigs, which lead to more nitrogen (N) excreted in the faeces and urine. N can be emitted to the air in the form of e.g. ammonia (NH3), which contributes to eutrophication and acidification and as nitrous oxide (N2O), which is a very potent greenhouse gas. The emission of N can be reduced by e.g.